Ausom DT2 PRO 52V - 58.8V 4A Fast Charger

Ausom DT2 Pro Fast Charger – 52V (58.8V – 4A) – Active Cooling

This 4A fast charger for the Ausom DT2 Pro delivers a 58.8V output. It is designed for the original 52V (14S) lithium-ion battery configurations detailed below.

It uses the original red 3-pin Ausom connector shown in the photos, allowing it to plug directly into the corresponding charging port on your electric scooter.

Its 4A current reduces charging time compared to the standard 2A version. It is suitable for quickly recovering range between two trips.

This charger is equipped with active cooling to promote efficient heat dissipation during long charging sessions. This version has a plastic casing.

Technical specifications

• Output voltage: 58.8V DC.
• Charging current: 4A.
• Battery type: 52V (14S) lithium-ion.
• Connector: original red 3-pin Ausom connector.
• Casing: plastic.
• Cooling: Active Cooling.
• Estimated charging time for Ausom DT2 Pro (23.4 Ah): ≈ 5 h 45.
• Weight: 0.6 kg.
• Built-in protections: overvoltage, overcurrent, overheating, and short-circuit.
• LED indicator: red = charging / green = charge complete.
• Contents: Source’IT charger and power cord.

A charger adapted to the Ausom DT2 Pro

The Ausom DT2 Pro uses a 52V 23.4 Ah lithium-ion battery. Its high capacity is suitable for long trips, but requires more charging time with a standard 2A current. The 4A and 5A versions allow for faster range recovery between trips.

• Ausom DT2 Pro: 52V 23.4 Ah (1216.8 Wh) lithium-ion battery.

The 52V nominal voltage refers to the battery; the 58.8V voltage corresponds to its maximum charging voltage. The choice of charger also depends on the connector and its wiring. This product page is intended for the original configurations listed, with the pictured connector.

The advantages of this 4A version

• Output regulated at 58.8V for the corresponding 52V configuration.
• Original red 3-pin Ausom connector visible in the photos.
• Fast charging to reduce wait times compared to 2A.
• Active cooling to exhaust internal heat.
• Plastic casing and integrated electronic protections.
• 2-year warranty and Source’IT technical support.

Comparing Ausom DT2 Pro chargers

The versions in this range deliver the same final voltage of 58.8V. The charging current, casing, and estimated duration distinguish the products. The 2A is suitable for standard charging, the 4A for fast charging, and the 5A for even shorter charging times.

Ausom DT2 Pro – 23.4 Ah

• 2A standard: ≈ 11 h 30
• 4A fast: ≈ 5 h 45
• 5A ultra-fast: ≈ 4 h 30

These durations are estimates for a 0 to 100% charge using a single charger, calculated by dividing the battery capacity in Ah by the charging current in A, then rounding down to the nearest quarter hour. The starting level, temperature, and battery condition will cause the actual time to vary.

• Ausom DT2 Pro 52V – 58.8V 2A standard charger
• Ausom DT2 Pro 52V – 58.8V 4A fast charger
• Ausom DT2 Pro 52V – 58.8V 5A ultra-fast charger

Find all Ausom DT2 Pro chargers to compare versions and verify their photos.

Safety and reliability

The 58.8V regulation and electronic protections accompany the charging of the corresponding 52V battery. Active cooling cools the charger; it does not directly cool the battery. Keep the vents clear and allow a hot battery to cool down after use.

FAQ – Ausom DT2 Pro 4A Charger

Is this charger suitable for my scooter?

It corresponds to the models and batteries listed in the compatibility section, with the pictured original red 3-pin Ausom connector. Check the exact model, voltage, and plug of your version before choosing.

How long does charging take?

Ausom DT2 Pro 23.4 Ah: approximately 5 h 45 with this 4A charger. A partially charged battery will take less time.

Does the charger have a fan?

Yes. This 4A version features Active Cooling and a plastic casing. The fan may be audible during charging.

Can I keep it as a second charger?

Yes, to have a charger at another charging location. The simultaneous use of two chargers depends on the ports and the total current accepted by the scooter version; it cannot be assumed simply by the presence of two sockets.

What is the difference compared to other power levels?

The 4A reduces charging time compared to the 2A standard. The list and links above allow you to compare other versions for your battery's exact capacity.

Warranty, shipping, and support

• 2-year warranty on the Source’IT charger.
• Shipping within 24/48 hours from France.

Need a compatibility check? Email contact@source-it.fr with the exact model, a photo of the charging port, and the battery information.

Photos are for illustrative purposes only – Source’IT.