UrbanGlide EON X Electric Scooter Ultra-Fast Charger 60V-67.2V 5A

UrbanGlide EON X Electric Scooter Ultra-Fast Charger 60V-67.2V 5A

Need a reliable UrbanGlide EON X charger to replace your current one or to have a second charging solution on hand? This 5A UrbanGlide EON X ultra-fast charger is designed for its 60V 30Ah lithium-ion battery. It delivers a regulated output voltage of 67.2V and uses the GX16-3 connector specific to this scooter.

With its 5A current, this ultra-fast UrbanGlide EON X charger is intended for high-capacity batteries and intensive users. It significantly reduces charging time while maintaining a stable and regulated voltage. This charger is equipped with active ventilation, which promotes efficient heat dissipation during long charging sessions.

Technical specifications of the UrbanGlide EON X ultra-fast charger

• Compatible model: UrbanGlide EON X
• Compatible battery: 60V 30Ah lithium-ion
• Output voltage: 67.2V
• Charging current: 5A – ultra-fast charge
• Charging connector: GX16-3
• Approximate charging time: about 6 hours
• Casing: aluminum
• Cooling: Active ventilation
• LED indicator: visual charge monitoring
• Built-in protections: overload, overvoltage, overcurrent, short-circuit, and overheating

Comparison of charging times

• 2A charger: about 15 hours
• 5A ultra-fast charger: about 6 hours

These durations are estimates calculated based on battery capacity and charging current. The final balancing phase managed by the BMS may slightly extend the charging time.

Dedicated compatibility for the UrbanGlide EON X

The 60V 30Ah battery of the UrbanGlide EON X requires a precise charging voltage of 67.2V. The charger's electronics regulate this voltage throughout the entire charge to properly supply the battery's BMS. The GX16-3 connector ensures compatibility with this model's charging port.

The 5A current offers an ultra-fast charge with an estimated full duration of 6 hours. The actual time depends on the battery level when plugged in, its temperature, its condition, and the final balancing phase.

Why choose this UrbanGlide EON X charger?

• Targeted compatibility: 60V 30Ah battery and 67.2V output
• GX16-3 connector: format corresponding to the UrbanGlide EON X
• Active ventilation: efficient heat dissipation during prolonged charges
• Regulated charge: stable 5A current
• Electronic safety: protection against major electrical faults
• Pre-shipment inspection: each charger is verified by Source'IT
• 2-year warranty: assistance available if needed

Safety and reliability during charging

This charger for the UrbanGlide EON X incorporates several electronic protections to secure the battery and the charging cycle. The active ventilation helps maintain a controlled operating temperature, while the LED indicator shows the charging status. To preserve the battery, plug the charger into a dry, ventilated area and allow the charge to complete normally.

FAQ – UrbanGlide EON X Electric Scooter Ultra-Fast Charger 60V-67.2V 5A

Is this charger compatible with the UrbanGlide EON X?

Yes. It is configured for the 60V 30Ah battery, the 67.2V output voltage, and the GX16-3 connector of the UrbanGlide EON X.

How long does it take to charge the battery?

A full charge takes about 6 hours with this 5A charger. Time may vary depending on the starting level and the BMS balancing phase.

Does the charger have active ventilation?

Yes. This charger is equipped with active ventilation which promotes efficient heat dissipation during long charging sessions.

What is the LED indicator for?

The indicator allows you to easily monitor the charger's operating status and the progress of the charge.

Can I use this charger on another UrbanGlide model?

Use it only with a battery whose nominal voltage, charging voltage, and connector match exactly the specifications indicated on this sheet.

Source'IT warranty, shipping, and support

• Fast shipping from France
• 2-year warranty
• Charger checked before shipment
• Technical support via email

Do you have a question about this 5A UrbanGlide EON X ultra-fast charger? Contact Source'IT at contact@source-it.fr.

*Photos are not contractually binding – Source'IT.